EFFICIENCY
RATING
CERTIFIED
USER’S INFORMATION
MANUAL
MODELS:
ISO 9001
Certified Quality
Management System
All Residential Multi-position Gas Furnaces
(33” Models)
TABLE OF CONTENTS
CONTACT INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
How to Clean your Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
BLOWER CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
MOTOR LUBRICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
INSTRUCTIONS FOR EXAMINING THE
FURNACE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
START-UP AND SHUTDOWN INSTRUCTIONS . . . . . . . . . . . . . . . . 3
HOW YOUR GAS FURNACE WORKS . . . . . . . . . . . . . . . . . . . . . . 3
OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
TO TURN OFF THE APPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SERVICE INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
TROUBLESHOOTING PROBLEMS . . . . . . . . . . . . . . . . . . . . . . . . .5
FURNACE CONTROL DIAGNOSTICS . . . . . . . . . . . . . . . . . . . . . . .5
FURNACE MAINTENANCE - DEALER/CONTRACTOR . . . . . . . . .5
REPLACEMENT PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
FURNACE MAINTENANCE - USER INFORMATION . . . . . . . . . . . . 4
EXTERNAL AIR FILTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
CONTACT INFORMATION
•
•
Contact us by mail:
Johnson Controls Unitary Products
Consumer Relations
5005 York Drive
Norman, OK 73069
1. The furnace area must be kept clear and free of combustible mate-
rials, gasoline and other flammable vapors and liquids.
We recommend that the user read all sections of this
manual and keep the manual for future reference.
2. Insulating materials may be combustible. The furnace must be
kept free and clear of insulating materials. The furnace area must
be examined when installed in an attic or other insulated space or
when insulation is added to be sure that the insulation material has
been kept away from the furnace.
FIRE OR EXPLOSION HAZARD - Failure to follow safety warnings
exactly could result in serious injury, death, or property damage.
3. The furnace needs air for combustion in order to operate properly
and safely. Do not block or obstruct air openings on the furnace,
air openings to the area where the furnace is installed, or spaces
around the furnace.
—
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
—
WHAT TO DO IF YOU SMELL GAS:
•
•
Do not try to light any appliance.
4. Follow the instructions exactly as shown on the OPERATING
INSTRUCTION LABEL on the furnace or the “START-UP AND
SHUTDOWN INSTRUCTIONS” section of this manual when light-
ing the furnace or turning the furnace off.
Do not touch any electrical switch; do not use any phone (includ-
ing cell phone) in your building.
•
•
Leave the building immediately.
Immediately call your gas supplier from a neighbor’s phone. Fol-
low the gas supplier’s instructions.
5. Should the gas supply fail to shut off or if overheating occurs, shut
off the gas valve to the furnace before shutting off the electrical
supply.
•
If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified
installer, service agency or the gas supplier.
—
6. Do not use this furnace if any part has been under water. A flood-
damaged furnace is extremely dangerous. Attempts to use the fur-
nace can result in fire or explosion. A qualified service agency
should be contacted to inspect the furnace and replace all gas
controls, control system parts, electrical parts that have been wet
or the furnace if deemed necessary.
SECTION I: SAFETY
This is a safety alert symbol. When you see this symbol on
labels or in manuals, be alert to the potential for personal
injury.
7. NEVER . . .Store flammable materials of any kind near your fur-
nace. Gasoline, solvents, and other volatile liquids should be
stored only in approved containers outside your home. These
materials vaporize easily and are extremely dangerous.
Understand and pay particular attention to the signal words DANGER,
WARNING, or CAUTION.
DANGER indicates an imminently hazardous situation, which, if not
avoided, will result in death or serious injury.
8. NEVER . . .Store cleaning materials near your furnace. Materials
such as bleaches, detergents, powdered cleansers, etc., can
cause corrosion of the heat exchangers.
WARNING indicates a potentially hazardous situation, which, if not
avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation, which, if not
avoided may result in minor or moderate injury. It is also used to
alert against unsafe practices and hazards involving only property dam-
age.
9. NEVER . . . Use the area around your furnace as a storage area
for items which could block the normal flow of air. This flow of air is
required for ventilation of the various furnace components.
356486-UUM-H-0609
356486-UUM-H-0609
Rollout
Safety Switch
Rollout
Safety Switch
Flame Sensor
Manifold
Pipe
Manifold
Pipe
Flame Sensor
Gas Valve
Ignitor
Ignitor
Gas Valve
Limit Switch
(Behind gas valve)
Limit Switch
(Behind gas valve)
Vent Pipe
Vent Pipe
Draft Inducer
Assembly
Draft Inducer
Assembly
Electrical
Junction Box
Electrical
Junction Box
Pressure
Switch
Pressure
Switch
Silicone Tube
Silicone Tube
Condensate
Pan
Condensate
Pan
Safety
Door Switch
Safety
Door Switch
Control
Board
Control
Board
Transformer
Blower
Transformer
Blower
Power Factor
Choke (Not
used on all
models)
Capacitor
ECM MOTOR
PSC MOTOR
FIGURE 5: Component Location - 97% Modulating PSC Models
FIGURE 6: Component Location - 97% Modulating ECM Models
1. Examine the heat exchanger, vent pipe, combustion air passages,
vent connectors and chimney to be sure they are clear and free of
obstructions.
SECTION III: START-UP AND SHUTDOWN
INSTRUCTIONS
Read the Instructions Below Before Trying to Start the
Furnace!
2. Examine the vent pipe making sure it is firmly in place, that it
slopes slightly upward and is physically sound without holes and
all of the connections are secure.
3. Examine the return-air duct connections to make sure they are
physically sound, sealed to the furnace casing, and the ducts ter-
minate outside the space containing the furnace.
If you do not follow these instructions exactly, a fire or explo-
sion may result causing property damage, personal injury,
and/or loss of life.
4. Examine the furnace casing making sure the physical support is
sound without sagging, cracks or gaps. Examine the furnace base
making sure it is physically sound without cracks, gaps or sagging
and has a good seal.
HOW YOUR GAS FURNACE WORKS
Your furnace is a very easy appliance to take for granted. Season after
season, it sits there in your home, keeping you warm and comfortable.
For this reason, you may never have given much thought to the way
your furnace operates. In order to get the safest and most efficient oper-
ation from your furnace, you should understand how your furnace does
its job.
5. Examine the furnace casing for obvious signs of deterioration.
6. Examine the burner flames to make sure they are in good adjust-
ment. Refer to the pictorial sketch shown in Figure 7 as a compar-
ison to the actual flame.
Blue Cone Portion of Flame Should
Enter Heat Exchanger Tube
When you set your thermostat to provide more heat in your home, you
are starting the heating cycle of the furnace. First, the inducer motor
starts to purge the heat exchanger of any remaining gases. Next, the
hot surface ignitor glows and after a warm-up period the gas valve
opens and ignition occurs. A short time later, the blower starts and dis-
tributes the warm air throughout the home. When the temperature set-
ting on your thermostat is reached, the gas valve closes, the main
burners are turned off, and the blower continues to run until the remain-
ing warm air in the system is distributed. When the blower stops, the
heating cycle has ended.
1. This appliance does not have a pilot. It is equipped with an ignition
device which automatically lights the burner. Do not try to light the
burner by hand.
FIGURE 7: Burner Flame Drawing (Upflow Configuration Shown)
2. BEFORE OPERATING; smell all around the appliance area for
gas. Be sure to smell next to the floor because some gas is
heavier than air and will settle on the floor.
7. Examine and replace external air filters as needed to make sure
they are not blocked, and proper airflow is provided to the furnace.
8. Examine any installed accessories or system components such as
evaporator coils to insure proper operation, drainage of conden-
sate, and that there is no water leakage or damage to the furnace
or any components.
3. Use only your hand to push the gas control switch to the ON posi-
tion. Never use tools. If the switch will not operate by hand, don’t
try to repair it, call a qualified service technician. Force or
attempted repair may result in a fire or explosion.
4. Do not use this appliance if any part has been under water. Imme-
diately call a qualified service technician to inspect the appliance
and to replace any part of the control system and any gas control,
which has been under water.
Johnson Controls Unitary Products
3
356486-UUM-H-0609
OPERATING INSTRUCTIONS
HIGH STAGE REGULATOR
ADJUSTMENT
1. STOP! Read the safety information above for your protection.
2. Set the thermostat to the lowest setting in the heat mode.
3. Turn off all electric power to the appliance.
OUTLET
PRESSURE
PORT
VENT
PORT
4. Remove furnace burner access panel/door.
5. Move gas control switch to the OFF position. Do not force. See
Figures 9-11.
INLET
OUTLET
6. Wait five (5) minutes to clear out any gas. If you then smell gas,
STOP! Follow “B” in the safety information above. If you don’t
smell gas, go to next step.
WRENCH
BOSS
INLET
PRESSURE
PORT
7. Move gas control switch to the ON position. Do not force. See Fig-
ures 9-11.
LOW STAGE REGULATOR
ADJUSTMENT
ON OFF
SWITCH
8. Replace furnace burner access panel/door.
9. Turn on all electric power to the appliance.
FIGURE 10: Two-Stage Gas Valve
10. Set thermostat to the desired setting. Burner will light, which may
take 30-60 seconds.
11. After three (3) trials for ignition, if the appliance will not operate fol-
low the instructions, “TO TURN OFF THE APPLIANCE” and call
your service technician or gas supplier.
TO TURN OFF THE APPLIANCE
1. Set the thermostat to lowest setting in heating mode.
Main
Regulator
Adjustment
2. Turn off all electric power to the appliance if service is to be per-
formed.
On/Off
Knob
3. Remove furnace burner access panel/door.
Outlet
Pressure
Tap
Inlet
Pressure
Tap
4. Move gas control switch to the “OFF” position. See Figures 9-11.
5. Replace furnace burner access panel/door.
FIGURE 11: Modulating Gas Valve
SECTION IV: FURNACE MAINTENANCE -
USER INFORMATION
Should overheating occur, or the gas valve fail to shut off, turn
the external manual gas valve in the gas supply line to the fur-
nace to the “off” position and let the furnace cool off before
shutting off the electrical power supply.
Before proceeding, be sure the area is well ventilated. Turn the
thermostat OFF. If the blower is running, wait until it stops auto-
matically. Turn OFF the gas and electrical power supplies to the
furnace. Check all metal parts and surfaces to be sure they
have cooled to room temperature before you begin.
External Manual
Shutoff Valve
To Gas
Supply
To Gas
Supply
EXTERNAL AIR FILTERS
Filters used with this furnace must be installed external to the furnace
casing. DO NOT attempt to install filters inside the furnace cabinet.
Grounded Joint Union
may be Installed
Inside or Outside Unit.
Some installations may have the air filter in a rack attached to the cas-
ing of the furnace or placed in the return air duct. If the filter location or
replacement process is not obvious, contact your installer or service
technician for assistance.
Drip Leg
FIGURE 8: Gas Piping
Every time the external air filters are changed the following items should
be visually inspected:
Outlet
Pressure
Port
Vent Port
Outlet
•
•
Check combustion air and vent pipe for blockage or leakage.
Check all components to be sure they are in good condition and
that there are no obvious signs of deterioration.
Inlet
•
•
Check the drain lines to make sure there are no cracks or leaks.
Check for dirt or lint on any surfaces or on components. Do not try
to clean any of the surfaces or components. Cleaning of the fur-
nace and its components must be done by a qualified service pro-
fessional.
Wrench
Boss
Inlet
Main Regulator
Adjustment
Pressure
Port
On/Off Switch
(Shown in ON position)
FIGURE 9: Single Stage Gas Valve
4
Johnson Controls Unitary Products
356486-UUM-H-0609
FURNACE CONTROL DIAGNOSTICS
The furnace has built-in, self-diagnostic capability. If a system problem
occurs, a blinking LED shows a fault code. The LED can flash red,
green or amber to indicate various conditions. It is located behind a
clear view port in the blower compartment door.
If during the inspection of your furnace, you find any of the following
conditions:
•
•
•
•
Excessive amounts of dust and lint on components.
Damaged or deteriorated components or surfaces.
Leaks or blockage in the vent pipe passages.
Water on any surface inside or outside of the furnace.
The control continuously monitors its own operation and the operation
of the system. If a failure occurs, the LED will indicate the failure code. If
the failure is internal to the control, the light will stay on continuously. In
this case, the entire control should be replaced, as the control is not
field repairable.
Do not operate the furnace, call a certified dealer or servicing contractor
to check or clean your furnace, or for more information if you have
questions about the operation of your furnace.
If all components appear to be in good operating condition, replace the
furnace access panels/doors. Turn ON the gas and electrical power
supplies to the furnace, and set thermostat to the desired temperature.
Flash sequence codes 1 through 10 are as follows: LED will turn ON for
1/4 second and OFF for 1/4 second. This pattern will be repeated the
number of times equal to the code. For example, six ON flashes equals
a number 6 fault code. All flash code sequences are broken by a 2 sec-
ond OFF period.
How to Clean your Filter
High-velocity filters may be cleaned with a vacuum cleaner or washed
with a garden hose. Be sure to shake off excess water and allow filter to
completely dry before re-installing the filter.
SLOW GREEN FLASH: Normal operation.
DOUBLE AMBER FLASH: Normal heating operation - Modulating Fur-
nace Models Only
Replace throw away filter(s) with the same size new filter(s). Throw
away filter(s) may be replaced with cleanable filter(s) at this time.
SLOW AMBER FLASH: Normal operation with call for heat.
BLOWER CARE
RAPID RED FLASHES: There is a problem with the operation of this
furnace. Contact your local dealer, contractor or service provider.
Even with good filters properly in place, blower wheels and motors will
become dust laden after months of operation. The entire blower assem-
bly should be inspected annually. This service must be performed by a
qualified service agency.
FURNACE MAINTENANCE - DEALER/CONTRACTOR
The furnace should be cleaned and adjusted by a certified dealer or
qualified service contractor once a year or before the start of every
heating season. The following items must be cleaned and serviced or
replaced if there are signs of deterioration.
NOTE: The spring-loaded safety cut-off switch, mounted at the blower
deck will automatically cut off the electrical power supply to the furnace
when the furnace blower access panel/door is removed. As a safety
precaution, all electrical power and the gas supply to the furnace should
be turned off before servicing.
1. The vent terminal.
2. The furnace vent and combustion air intake passageways. Should
it be necessary to service the vent/air intake system, the manufac-
turer recommends this service be conducted by a qualified service
agency. The operation of this appliance requires the reassembly
and resealing of the vent/air intake system.
Make sure you DO NOT move the clip on weight on the
indoor fan wheel when cleaning the wheel. This weight is
used to balance the wheel. Moving the weight will cause the
fan wheel to vibrate.
3. The furnace burners, ignitor and flame sensor.
4. The condensate collection and disposal system. If any disassem-
bly of components containing flue or vent gases is required, a
qualified service agency must perform the service.
MOTOR LUBRICATION
5. Heat exchanger assembly.
The motors in these furnaces are permanently lubricated, and do not
require periodic oiling.
6. Induced draft motor assembly.
REPLACEMENT PARTS LIST
SECTION V: SERVICE INFORMATION
All components, assemblies, accessories, and replacement parts for
this furnace are available through qualified service agencies. It is not
recommended that the user purchase, install, or replace any compo-
nents of this furnace. Contact your local contactor, dealer, or service
provider for additional information.
TROUBLESHOOTING PROBLEMS
If your furnace is not operating correctly, the following visual checks
should be made before contacting your local contractor, dealer, or ser-
vice provider.
1. Check that electrical power to the furnace is turned on.
2. Check that the manual gas shut-off valve in the gas piping supply
is turned to the ON position. Refer to Figure 9.
WIRING DIAGRAM
The unit wiring diagram may be found on the inside of one of the access
panels on the furnace. It is intended for reference only. If service is
required, contact your local contactor, dealer, or service provider.
3. Check that the ON/OFF switch on the gas valve is turned to the
ON position. Refer to Figures 9, 7 or 8.
4. Check that the furnace blower access panel/door is correctly posi-
tioned. The electrical power supply will be cut off if this door is
removed.
Johnson Controls Unitary Products
5
Limited Warranty
Johnson Controls Unitary Products (hereinafter “Company”) warrants this product to be free from defects in factory workmanship and material under normal
use and service and will, at its option, repair or replace any parts, without charge, subject to the exclusions below, that prove to have such defects according to
the terms outlined on this warranty. This warranty covers only the equipment described by the Product Model Number and Serial Number on the equipment or
listed on the Warranty Registration Card and applies only to products installed in the United States or Canada.
FOR WARRANTY SERVICE OR REPAIR:
Contact the installer or a Company dealer. You may find the installer’s name on this page or on the equipment. You can also find a Company dealer online at
www.yorkupg.com. For help finding a servicing dealer, contact: Johnson Controls Unitary Products, Consumer Relations, 5005 York Drive, Norman, OK
73069. Or, by phone 877-874-7378. All warranty service or repair will be performed during regular business hours, Monday through Friday 9:00am-5:00pm.
Product Model No.__________________________________
Unit Serial No._____________________________________
Installation Date_________________________________________
Installing Dealer_________________________________________
FOR PRODUCT REGISTRATION: For your benefit and protection, return the Warranty Registration Card to Company promptly after installation. This will ini-
tiate the warranty period and allow us to contact you, should it become necessary. For this warranty to apply, the product must be installed according to Com-
pany recommendations and specifications, and in accordance with all local, state, and national codes; and the product must not be removed from its place of
original installation. The warranty period for repair or replacement parts provided hereunder shall not extend beyond the warranty period stated below. In the
absence of a recorded Warranty Registration Card, the warranty period will begin upon product shipment from Company. If you are unaware of the date the
ductregistration.com or by returning the Warranty Registration Card on the back page of this packet.
HEAT EXCHANGER WARRANTY ADDITIONAL TERMS: Company warrants the heat exchangers (primary and/or secondary, if applicable) in this product to
be free from defects in factory workmanship and material under normal use and service and will at its option, repair or furnish a replacement heat exchanger,
either new or reconditioned that meets the intended fit, use and function of the original heat exchanger. Alternatively, Company may, at its option, extend a
replacement allowance to be applied toward the purchase of a new furnace marketed by Company. The exact amount of the allowance will be determined at
the discretion of Company, based upon current market conditions, but in no case shall this allowance exceed thirty (30) percent of the original consumer pur-
chase price of the furnace, excluding such items as ductwork, wiring, piping, and installation costs. Company shall have no responsibility hereunder for instal-
lation, shipping, handling or other charges except as specifically provided herein.
The warranty period in years, depending on the part and the claimant, is as shown in the chart below.
HEAT EXCHANGER
Residential Applications
FURNACE TYPE
PARTS
Non-Residential
Applications
Subsequent
Owner
Original Owner
20
20
N/A
N/A
20
10
10
10
5
5 or 10†
5
GG8S,GGLS
TM8X,TMLX,TM8T,TMLT,TM8V,TMLV,TG8S,TGLS
GG9S
Lifetime
TM9V,TM9T,TM9X,TG9S
TP9C,TP8C,TPLC,TM9M,TM8M,TMLM,YP9C,YP8C,YPLC,YM9M,YM8M,YMLM
CP9C,CP8C,CPLC,CM9M,CM8M,CMLM,LP9C,LP8C,LPLC,LM9M,LM8M,LMLM
Lifetime
20
10
5 or 10†
†
or 90 days of closing for new home construction. In some states, registration is not required, but proof of installation may is required to qualify for the 10-year parts
warranty. Guardian Brand products have a 5-year compressor and 5-year parts warranty and are not eligible for the 10-year parts warranty.
Company strongly recommends regular periodic preventative maintenance on this equipment. The person most familiar with the equipment in your HVAC sys-
tem is a Company dealer. The Company dealer can ensure your maintenance program meets the conditions of the "Company Warranty", maximize the effi-
ciency of the equipment, and service your unit within the mandated guidelines with regard to unlawful discharge of refrigerants into the atmosphere.
EXCLUSIONS:
This warranty does not cover any:
1.
2.
Shipping, labor, or material charges or damages resulting from transportation, installation, or servicing.
Damages resulting from accident, abuse, fire, flood, alteration, or acts of God (tampering, altering, defacing or removing the product serial number will
serve to void this warranty).
3.
4.
5.
6.
7.
Damages resulting from use of the product in a corrosive atmosphere.
Damages resulting from inadequacy or interruption of electrical service or fuel supply, improper voltage conditions, blown fuses, or other like damages.
Cleaning or replacement of filters or damages resulting from operation with inadequate supply of air or water.
Damages resulting from failure to properly and regularly clean air and/or water side of condenser and evaporator.
Damages resulting from: (I) freezing of condenser water or condensate; (II) inadequate or interrupted water supply; (III) use of corrosive water; (IV) fouling
or restriction of the water circuit by foreign material or like causes.
8.
9.
Damages resulting from use of components or accessories not approved by Company (vent dampers, etc.).
Increase in fuel or electric cost.
This warranty is in lieu of all other warranties, expressed or implied, including the implied warranties of merchantability and fitness for a particular
purpose.
Some states do not allow the disclaimer of implied warranty, so that the above disclaimer may not apply to you. Some states only allow a partial
limitation on implied warranties to limit the duration of implied warranties to the duration of the express warranty. In such states, the duration of
implied warranties is hereby expressly limited to the duration of the express warranty on the face hereof. Some states do not allow limitations on
how long an implied warranty lasts, so the above limitation may not apply to you.
In no event, whether as a result of breach of warranty or contract, tort (including negligence), strict liability, or otherwise, shall Company be liable
for special, incidental, or consequential damages, including but not limited to loss of use of the equipment or associated equipment, lost revenues
or profits, cost of substitute equipment or cost of fuel or electricity. The above limitations shall inure to the benefit of Company’s suppliers and
subcontractors. The above limitation on consequential damages shall not apply to injuries to persons in the case of consumer goods.
Company does not assume, or authorize any other person to assume for Company, any other liability for the sale of this product. Some states do
not allow the exclusion or limitation of incidental or consequently damages, so the above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
Subject to change without notice. Printed in U.S.A.
356486-UUM-H-0609
Copyright © 2009 by Johnson Controls, Inc. All rights reserved.
Supersedes: 356486-UUM-G-0409
Johnson Controls Unitary Products
5005 York Drive
Norman, OK 73069
|